TITAN FLOW CONTROL CATALOG - 0120

CV12-0118

SWING CHECK VALVE f WAFERTYPE f SHORT PATTERN ASME CLASS 150 f CARBON STEEL & STAINLESS STEEL

TITAN

®

TITAN FLOW CONTROL, INC.

S IZES : 2" ~ 24"

MODELS: CV 12-CS Body: Carbon Steel Seat/Seal: Buna-N

F FEATURES s

CV 12-SS Body: Stainless Steel Seat/Seal: PTFE

robust design th is is a s el f - act ing , non - re turn , s ingl e plat e , waf er ty pe swing check valve wh ich provides h igh qual ity and re l iab il ity wi th in a s impl if i ed cons tructi on . ava ilab l e in both carbon s te el and s tai nl es s s te el . s minimal head loss the low ine rti a d isc is des igned to open and clos e under low d if f er enti al pr es sure cond it ions . al so , the short patt ern des ign and s tra ight f low path minimize pr es sure drop acros s the valve . s economi cal design the low we ight and short face - to - face d imens ions provide an economical , s pace - s av ing soluti on . addi ti onal ly , f lange gas ket s ar e ty pical ly not requi red due to the bu ilt - in , body s eal o - ri ngs . s res il ient soft seats sof t s eat s ( pt f e or buna ) comb ined wi th a gravi ty as s is ted d isc hel p to ensur e a pos iti ve shutof f wh ich cr eate s a bubb l e ti ght s eal that mee ts or exce eds api 598 l eakage requi rement s . s versat i le design th is valve can be ins tal l ed be tween we ld neck or s l i p - on ty pe compani on f langes of d if f er ent s tandards . th is valve can not be ins tal l ed in a ve rti cal pi pel ine wi th downward f low . s fugi t i ve emi ssion design the one - pi ece body des ign el i minates potential l eak paths to the env ironment so ther e ar e no body emi s si ons .

T TECHNICAL

PRESSURE/ TEMPERATURE RATING (1) CS - ASTMA515 GR. 70 - CLASS 150

WOG (Non-shock) : 285 PSI @ 100 °F

PRESSURE/ TEMPERATURE RATING (1) SS - ASTMA240 GR. 316 - CLASS 150

WOG (Non-shock) : 275 PSI @ 100 °F

SEAT AND BODY SEAL (O-RING) (1) TEMPERATURE RANGE

PTFE: -100 ~ 400 °F BUNA-N: -20 ~ 250 °F

1. The above listed temperatures are theoretical and may vary during actual operating conditions.

markets : oil and gas production , general industry , chemical , & petrochemical service : this valve is intended for low flow service that is steady , clean ( no abrasives or solids ), and non - pulsating . flow rate must not exceed for liquids : 15 ft / sec ptfe properties : good for most chemical environments . offers excellent tear , abrasive , chemical , acid , and alkali resistance . not recommended for high pressure steam or large temperature variations . buna - n properties : most widely used elastomer . good for most petroleum oils and fluids , silicone greases and oils , and cold water . excellent compression set , tear , and abrasion resistance . poor weather resistance and moderate heat resistance . not recommended for severe ozone - resistant applications . The above data represents common market and service applications. No representation or guarantee, expressed or implied, is given due to the numerous variations of concentrations, temperatures and flow conditions that may occur during actual service.

A

APPLICATIONS

Tel: 910-735-0000 s Fax: 910-738-3848 s titan@titanfci.com s www.titanfci.com YOUR PIPELINE TO THE FUTURE! TITAN FLOW CONTROL, INC.