TITAN FLOW CONTROL CATALOG - 0120

CV32-0120

SWING CHECK VALVE f WAFER TYPE f SINGLE DISC ASME CLASS 150 f CARBON AND STAINLESS STEEL

TITAN

TITAN FLOW CONTROL, INC.

MODELS: CV 32-CS (Carbon - Vi ton) CV 32-SS ( S t a i n l ess - PTFE)

F FEATURES

S IZES : 2" ~ 12"

s ECONOMI CAL DESIGN LOW WE IGHT AND SHORT LAYING L ENGTH PRODUCE S AV INGS IN INI TI AL COS T , S PACE REQUI REMENT S , AND INS TAL LATI ON WHEN COMPAR ED TO FUL L - BODY , SWING - TY PE CHECK VALVE S . s MINIMAL HEAD LOSS HEAD LOSS IS MINIMIZED BY PROVID ING A SHORT , S TRA IGHT AND VI RTUAL LY UNOB STRUCT ED F LOW PATH . ADDI TI ONAL LY , THE S PRING - LOADED D ISC IS DES IGNED WI TH VE RY LOW CRACKI NG PR ES SURE WH ICH REDUCE S THE AMOUNT OF ENE RGY REQUI RED TO OPEN THE VALVE . s QUI CK CLOSURE TO REDUCE WATER HAMMER SHUT - OF F IS ACH IE VED VI A THE FUL LY AUTOMAT IC , S PRING - AS S IS TED D ISC THAT CLOS ES NEAR ZERO F LOW VE LOCITY . THE L IGHTWE IGHT , S INGL E D ISC DES IGN CR EATE S A POS ITI VE SHUTOF F PR IOR TO F LOW RE VE RS AL WH ICH HEL PS TO KE EP SURGE S TO A MINIMUM . s DURABLE , HIGH QUAL ITY DESIGN THE CV 32 CHECK VALVE IS AVA ILAB L E IN EI THER CARBON S TE EL OR S TAI NL ES S S TE EL BODY CONF I GURATI ONS , WH ICH AL LOW IT TO PER FORM WE L L IN H IGHE R TEMPE RATUR E APPL I CATI ONS . THE CARBON S TE EL UNITS AR E EPOXY PA INT ED . ADDI TI ONAL LY , BOTH MODE L S F EATURE ANT I - CORROS I VE , S TAI NL ES S S TE EL TR IM ( D ISC , S PRING , SHA F T ) AS S TANDARD . s RES IL IENT SOFT SEATS RE S IL IENT SOF T S EAT S ( VI TON AND PT F E O - RI NG ) COUPL ED WI TH PR ECI SI ON MACH INED S EAL I NG SUR FACES HEL P TO ENSUR E A BUBB L E TI GHT S EAL THAT MEE TS OR EXCE EDS API 598 TE S T REQUI REMENT S . A APPLICATIONS

T TECHNICAL

PRESSURE/ TEMPERATURE RATING CS - ASTMA216 G R .WCB - CLASS 150

WOG (Non-shock) : 285 PSI @ 100 °F

PRESSURE/ TEMPERATURE RATING SS - ASTMA351 G R . CF8M - CLASS 150

WOG (Non-shock) : 275 PSI @ 100 °F

SEAT MATERIAL (O-RING) TEMPERATURE RANGE

VITON: -40 ~ 400 °F PTFE: -100 ~ 400 °F

SPRING MATERIAL MAXIMUMTEMPERATURE

Stainless Steel Type 304: 450 °F

1. The above listed temperatures are theoretical and may vary during actual operating conditions. 2. Max and min temperatures are for reference only. Prolonged use at these temperatures is not recommended for optimal service life.

MARKETS : GENERAL INDUSTRY , CHEMICAL , PETROCHEMICAL , POWER , AND FOOD & BEVERAGE SERVICE : INTENDED FOR LIQUID SERVICE THAT IS STEADY , CLEAN ( NO ABRASIVES OR SOLIDS ) AND NON - PULSATING . FLOW RATE SHOULD NOT EXCEED 15 FT / SEC . NOT RECOMMENDED FOR STEAM OR RECIPROCATING COMPRESSOR SERVICE . PTFE PROPERTIES : RECOMMENDED FOR MOST CHEMICAL ENVIRONMENTS INCLUDING ACIDS , B ASES , AND OILS . OFFERS EXCELLENT TEAR , ABRASIVE , CHEMICAL , ACID , AND ALKALI RESISTANCE . NOT RECOMMENDED FOR HIGH PRESSURE STEAM OR LARGE TEMPERATURE VARIATION APPLICATIONS . VITON PROPERTIES : OFFERS A BROAD RANGE OF CHEMICAL RESISTANCE AND EXCELLENT HEAT RESISTANCE . GOOD MECHANICAL PROPERTIES AND COMPRESSION SET RESISTANCE . OFTEN USED IN APPLICATIONS WHERE NOTHING ELSE WILL WORK . FAIR LOW TEMPERATURE RESISTANCE AND LIMITED HOT - WATER RESISTANCE AND SHRINKAGE . The above data represents common market and service applications. No representation or guarantee, expressed or implied, is given due to the numerous variations of concentrations, temperatures and flow conditions that may occur during actual service.

YOUR PIPELINE TO THE FUTURE! TITAN FLOW CONTROL, INC.

Fax: 910-738-3848 s titan@titanfci.com s www.titanfci.com

Tel: 910-735-0000 s

PO Box 7408 s

Lumberton, NC 28358

290 Corporate Drive s

Made with FlippingBook Publishing Software