TITAN FLOW CONTROL CATALOG - 0321

CV41-0221

CHECK VALVE f WAFER TYPE f DUAL DISC ASME CLASS 150 f DUCTILE IRON BODY

TITAN

TITAN FLOW CONTROL, INC.

SIZES 2" ~ 6" PROVIDE DUAL PRESSURE SERVICE ASME CLASS 150/300 (Scalloped Design)

MODEL: CV 41-DI Body : Duc t i l e I ron

Sea t s : Buna , Vi ton & EPDM Di scs : S t a i n l es s S tee l & Al umi num Bronze

s cost eff ic ient design low weight and short laying length produce savings in initial cost , space requirements , and installation when compared to full - body , swing - type check valves . s minimal head loss contour of body provides a short and straight flow path that generates very little turbulence . additionally , the spring - loaded discs are designed with very low cracking pressure which reduces the amount of energy required to open the valve . s qui ck closure to reduce water hammer shut - off is achieved via the fully automatic , spring - assisted discs that close near zero flow velocity . the lightweight , split disc design creates a positive shutoff prior to flow reversal and helps to keep slamming and surges to a minimum . s duct i le iron body ductile iron body maintains the anti - corrosive properties of cast iron while achieving a yield strength comparable to carbon steel . ductile iron also offers higher pressure / temperature ratings than cast iron . s res il ient soft seats resilient soft seats ( epdm , viton or buna ) ensure a bubble tight seal that meets or exceeds api 598 test requirements . s versat i le design sizes 2" through 6" are designed to fit bolt circle patterns for both cast iron ASME classes 125/300 and ductile iron ASME classes 150/300 . A APPLICATIONS F FEATURES S IZES : 2" ~ 24" LARGER SIZES AVAILABLE UPON REQUEST

Sizes 2" ~ 12"

T TECHNICAL

PRESSURE/ TEMPERATURE RATING DI - ASTMA536 - CLASS 150 - 2" ~ 24"

WOG (Non-shock) : 250 PSI @ 100 °F

PRESSURE/ TEMPERATURE RATING DI - ASTMA536 - CLASS 300 - 2" ~ 6" only

WOG (Non-shock) : 640 PSI @ 100 °F

SEAT MATERIAL TEMPERATURE RANGE

EPDM: -20 ~ 300 °F BUNA-N: -20 ~ 250 °F VITON: -40 ~ 400 °F

SPRING MATERIAL MAXIMUMTEMPERATURE

Series 300 Stainless Steel: 450 °F

1. The above listed temperatures are theoretical and may vary during actual operating conditions. 2. Max and min temperatures are for reference only. Prolonged use at these temperatures is not recommended for optimal service life.

buna - n properties : most widely used elastomer . good for most petroleum oils and fluids , silicone greases and oils , and cold water . excellent compression set , tear , and abrasion resistance . poor weather resistance and moderate heat resistance . not recommended for severe ozone - resistant applications . viton properties : offers a broad range of chemical resistance and excellent heat resistance . good mechanical properties and compression set resistance . often used in applications where nothing else will work . fair low temperature resistance and limited hot - water resistance and shrinkage . epdm properties : prob ably the most water resistant rubber available . it has good resistance to mild acids , alkalis , silicone oils / greases , ketones , alcohols and other polar solvents . it is not recommended for use with petroleum oils , di - ester lubricants , mineral oils , non - polar solvents or aromatic fuels . The above data represents common market and service applications. No representation or guarantee, expressed or implied, is given due to the numerous variations of concentrations, temperatures and flow conditions that may occur during actual service.

YOUR PIPELINE TO THE FUTURE! TITAN ® FLOW CONTROL, INC.

Fax: 910-738-3848 s titan@titanfci.com s www.titanfci.com

Tel: 910-735-0000 s

PO Box 7408 s

Lumberton, NC 28358

290 Corporate Drive s