TITAN FLOW CONTROL CATALOG - 1022
STRPDC-0121
TECHNICAL AND PERFORMANCE DATA PRESSURE DROP CHARTS f WYE & BASKET STRAINERS
TITAN
TITAN FLOW CONTROL, INC. WYE Strainers - Small Models Models: YS12 - YS52 - YS55 - YS56 - YS81 - YS82
WYE Strainers - Large Models
Models: YS58 - YS59 - YS54 - YS61 - YS62 - YS63 - YS64 - YS65
Sizes (in):
Sizes (in):
2 1/2
3/4
1
1 1/2
2
1/4
3
1/2
1 1/4
3/8
24
12
18
16
20
10
14
5
6
8
4
3
2 1/2
2
10
10
5 6 7
3 4 5 6 7
4
3
2
2
C v
C v
C v
C v
70
2200
4900
950
1600
6100
8000
3300
11000
570
400
260
160
110
1
22
42
70
110
38
15
2
160
8
0.7
1
0.3 0.4 0.5 0.6 0.7
0.7
0.5
0.4
0.3
0.2
0.2
0.1
0.1
20 30 40 50 70 100 200 300 500 700 1000 2000 3000 5000 10000 20000
50000
0.2 0.3 0.5 0.7 1
2 3 4 5 6 7 8 10
20 30 40 50 70 100 200 300 500 700 1000
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis)
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis)
WYE Strainers - High Pressure - Class 900 &1500
WYE Strainers - High Pressure - Class 2500
Models: YS66 - YS67 - YS68 - YS69 - YS83 - YS84
Models: YS70 - YS71 - YS86
Sizes (in):
Sizes (in):
8
10
3/4
6
1
1 1/2
1 1/4
10
1/2
1 1/2
2 1/2 - 3 4
4
6
2
8
3
2
10
3 4 5 6 7
5 6 7
4
3
2
2
C v
C v
C v
C v
1
450
30
42
600
100
375
160
34
650
6
32
60
930
180
140
11
16
1
0.3 0.4 0.5 0.6 0.7
0.7
0.5
0.4
0.3
0.2
0.2
0.1
0.1
1
2 3 4 5 6 7 8 10
20 30 40 50 70 100 200 300 500 700 1000 2000 3000 5000
5 6 7 8 10
20 30 40 50 60 70 100
200 300 400 500 700 1000
2000
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis)
Legend: Pressure Drop - PSI (y - axis) versus Flow Rate - GPM (x -axis)
Pressure Drop Equation for Liquids: ∆ P = G × (Q / Cv) 2 × Cr
∆ P = Pressure drop (psi)
G = Specific gravity of liquid
Q = Flow rate (GPM)
Cv = Flow coefficient factor Cr = Correction factor for mesh and viscosity
• These curves are theoretical; actual results may vary depending on installation conditions and other variables. Use these values for reference only. • The above pressure drop charts are based upon 1/8" perforated screens and baskets handling clean water at 60 °F during ideal inlet and outlet conditions. Therefore, they should only be used for estimation purposes. • For fluids other than water, multiply the pressure drop (∆ P) obtained from the charts by the specific gravity of the fluid in question. • For mesh lined screens, multiply the pressure drop (∆ P) obtained from the charts by the corresponding correction factor shown in the Cv correction table.
Tel: 910-735-0000 s Fax: 910-738-3848 s titan@titanfci.com s www.titanfci.com 290 Corporate Drive s PO Box 7408 s Lumberton, NC 28358 TITAN FLOW CONTROL, INC.
Made with FlippingBook - professional solution for displaying marketing and sales documents online