TITAN FLOW CONTROL CATALOG - 0817

CV12-1114

SWING CHECK VALVE f WAFERTYPE f SHORT PATTERN ANSI CLASS 150 f CARBON STEEL & STAINLESS STEEL

TITAN

®

TITAN FLOW CONTROL, INC.

S IZES : 2" ~ 24"

MODELS: CV 12-CS Body: Carbon Steel Seat/Seal: Buna-N

F FEATURES s

CV 12-SS Body: Stainless Steel Seat/Seal: PTFE

robust des ign th i s i s a s e l f - act i ng , non - r e turn , s i ngl e p lat e , wa f e r ty p e swi ng check valv e wh i ch p rov i de s h i gh qual i ty and r e l i ab i l i ty wi th i n a s i mp l i f i ed cons truct i on . ava i lab l e i n both carbon s t e e l and s ta i nl e s s s t e e l . s minimal head loss the low i ne rt i a d i sc i s de s i gned to op en and clos e unde r low d i f f e r ent i al p r e s sur e cond i t i ons . al so , the short patt e rn de s i gn and s tra i ght f low path m i n i m i ze p r e s sur e drop acros s the valv e . s economi cal des ign the low we i ght and short face - to - face d i mens i ons p rov i de an econom i cal , s pace - s av i ng solut i on . add i t i onal ly , f lange ga s ke t s ar e ty p i cal ly not r equ i r ed due to the bu i lt - i n , body s eal o - r i ngs . s res i l i ent soft seats sof t s eat s ( p t f e or buna ) comb i ned wi th a grav i ty a s s i s t ed d i sc he l p to ensur e a pos i t i v e shutof f wh i ch cr eat e s a bub b l e t i ght s eal that me e t s or exce eds ap i 598 l eakage r equ i r ement s . s versat i le des ign th i s valv e can b e i ns tal l ed b e twe en we ld neck or s l i p - on ty p e compan i on f lange s of d i f f e r ent s tandards . th i s valv e can not b e i ns tal l ed i n a v e rt i cal p i p e l i ne wi th downward f low . s fugi t i ve emi ss ion des ign the one - p i ece body de s i gn e l i m i nat e s pot ent i al l eak paths to the env i ronment so the r e ar e no body em i s s i ons .

T TECHNICAL

PRESSURE/ TEMPERATURE RATING (1) CS - ASTMA515 GR. 70 - CLASS 150

WOG (Non-shock) : 285 PSI @ 100 °F

PRESSURE/ TEMPERATURE RATING (1) SS - ASTMA240 GR. 316 - CLASS 150

WOG (Non-shock) : 275 PSI @ 100 °F

SEAT AND BODY SEAL (O-RING) (1) TEMPERATURE RANGE

PTFE: 14 ~ 320 °F BUNA-N: -20 ~ 250 °F

1. The above listed temperatures are theoretical and may vary during actual operating conditions.

markets : oil and gas production , general industry , chemical , & petrochemical service : this valve is intended for low flow service that is steady , clean ( no abrasives or solids ), and non - pulsating . flow rate must not exceed for liquids : 15 ft / sec ptfe properties : good for most chemical environments . offers excellent tear , abrasive , chemical , acid , and alkali resistance . not recommended for high pressure steam or large temperature variations . buna - n properties : most widely used elastomer . good for most petroleum oils and fluids , silicone greases and oils , and cold water . excellent compression set , tear , and abrasion resistance . poor weather resistance and moderate heat resistance . not recommended for severe ozone - resistant applications . The above data represents common market and service applications. No representation or guarantee, expressed or implied, is given due to the numerous variations of concentrations, temperatures and flow conditions that may occur during actual service.

A

APPLICATIONS

YOUR PIPELINE TO THE FUTURE! TITAN FLOW CONTROL, INC.

Fax: 910-738-3848 s titan@titanfci.com s www.titanfci.com

Tel: 910-735-0000 s

PO Box 7408 s

Lumberton, NC 28358

290 Corporate Drive s