TITAN FLOW CONTROL CATALOG - 0817

CV31-1014

SWING CHECK VALVE f WAFER TYPE f SINGLE DISC ANSI CLASS 125/150 f DUCTILE IRON

TITAN

TITAN FLOW CONTROL, INC.

NEWLY DESIGNED... Face to face meets API 594.

MODEL: CV 31-DI Body : Duc t i l e I ron Sea t : Buna -N Di sc : S t a i n l es s S tee l

F FEATURES

S IZES : 2" ~ 12"

s economi cal des ign low we i ght and short lay i ng l ength p roduce s av i ngs i n i n i t i al cos t , s pace r equ i r ement s , and i ns tal lat i on when compar ed to ful l - body , swi ng - ty p e check valv e s . s minimal head loss head los s i s m i n i m i zed by p rov i d i ng a short , s tra i ght and v i rtual ly unob s truct ed f low path . add i t i onal ly , the s p r i ng - loaded d i sc i s de s i gned wi th v e ry low crack i ng p r e s sur e wh i ch r educe s the amount of ene rgy r equ i r ed to op en the valv e . s qui ck closure to reduce water hammer shut - of f i s ach i e v ed v i a the ful ly automat i c , s p r i ng - a s s i s t ed d i sc that clos e s near ze ro f low v e loc i ty . the l i ghtwe i ght , s i ngl e d i sc de s i gn cr eat e s a pos i t i v e shutof f p r i or to f low r e v e r s al wh i ch he l p s to ke e p surge s to a m i n i mum . s durable , high qual i ty des ign the cv31 ' s duct i l e i ron body ma i nta i ns the ant i - corros i v e p rop e rt i e s of ca s t i ron wh i l e ach i e v i ng a y i e ld s tr ength comparab l e to carbon s t e e l . duct i l e i ron al so of f e r s h i ghe r p r e s sur e/t emp e ratur e rat i ngs than ca s t i ron i n the s ame p r e s sur e cla s s . the cv31 al so f eatur e s ant i - corros i v e , s ta i nl e s s s t e e l tr i m ( d i sc , s p r i ng , sha f t ) a s s tandard . s res i l i ent soft seats f i e ld r e p laceab l e , r e s i l i ent sof t s eat s ( buna - n o - r i ng ) coup l ed wi th p r ec i s i on mach i ned s eal i ng sur face s he l p to ensur e a bub b l e t i ght s eal that me e t s or exce eds ap i 598 t e s t r equ i r ement s . A APPLICATIONS

T TECHNICAL

PRESSURE/ TEMPERATURE RATING DI - ASTMA536 - CLASS 150 (1)

WOG (Non-shock) : 250 PSI @ 100 °F

SEAT MATERIAL TEMPERATURE RANGE

BUNA-N: -20 ~ 250 °F

SPRING MATERIAL MAXIMUMTEMPERATURE

Series 300 Stainless Steel: 450 °F

1. Ductile Iron valves offer higher pressure ratings than Cast Iron. valves For example, Ductile Iron valves (2" ~ 24") are rated at 250 psi wog. By comparison, Cast Iron valves (2" ~ 12") are rated at 200 psi wog and (14" ~ 24") are only rated at 150 psi wog.

markets : general industry , chemical , petrochemical , power , and food & beverage service : intended for liquid service that is steady , clean ( no abrasives or solids ) and non - pulsating . flow rate should not exceed 15 ft / sec . not recommended for steam or reciprocating compressor service . buna - n properties : most widely used elastomer . good for most petroleum oils and fluids , silicone greases and oils , and cold water . excellent compression set , tear , and abrasion resistance . poor weather resistance and moderate heat resistance . not recommended for severe ozone - resistant applications .

The above data represents common market and service applications. No representation or guarantee, expressed or implied, is given due to the numerous variations of concentrations, temperatures and flow conditions that may occur during actual service.

YOUR PIPELINE TO THE FUTURE! TITAN FLOW CONTROL, INC.

Fax: 910-738-3848 s titan@titanfci.com s www.titanfci.com

Tel: 910-735-0000 s

PO Box 7408 s

Lumberton, NC 28358

290 Corporate Drive s